Characteristics: 100% new and high quality Adopt of high-quality die head, long life, thread clear Ease of use, convenient to carry and durable Lightweight and compact hand design, save labor Apply to the thread work of galvanized pipe and iron pipe Powerful motor, increase work efficiency, shorten the construction time Includes 6 screw nozzle heads: 1/2 ", 3/4", 1 ", 1-1 / 4", 1-1 / 2 "& 2" Note: Keep adding the lubricating oil as you use it Package list: 1 x pipe thread 1 x pipe clamp 1 x fixed rod 2 x carbon brush 1 x oil can 6 times dies 1 x storage box. 2300W Electric Pipe Threader Threading Machine W/6 Dies 1/2" to 2" inches Clamps. 2300W 50HZ 25 r / min Electric tapping machine Pipe cutter 1/2, 3/4, 1, 1-1 / 4, 1-1 / 2, 2 inch. Item condition: New: newer, unused. Threading range: 20.9 - 49.6mm 1/2 - 2.Material: all copper wire machine. Voltage: 220 V, 50 Hz. Product dimensions: 57 x 14 x 31 cm. Nominal spindle speed: 25 (r / min). Size: 1/2, 3/4, 1, 1-1 / 4, 1-1 / 2, 2 (inches). Pipe outside diameter: 22,27,34,42,48,60mm. Inner pipe diameter: 15, 20, 25, 32, 40, 50 mm. Scope of application: Suitable for tapping galvanized pipes, iron pipes, PP pipes and pipes. Select the corresponding die head. The sheet is installed from the right on the host. Clamps, clamps the pipe approximately the same length as the arm (L2 is approximately equal to L1). Rotate the front and rear switches to the down arrow position to start the switch and auxiliary contacts. With hard pipes such as stainless steel pipes, galvanized pipes, brass when refueling in good time, plastic pipes without fuel. Note that the tube holder cannot be touched with the host during the right shift, otherwise it will injure the host. After the machine stops, pull the reverse switch up and exit the pipe. This product supports the use of standard pipes. This is our brand new electric tube threading machine, which is widely used in plant installation and construction industry. It is suitable for threading various water, electrical or gas pipes from 20.9 mm to 49.6 mm. With its powerful motor, this threader is an ideal device for increasing work efficiency, shortening construction time, ensuring construction quality and reducing labor intensity. This product is suitable for industrial and mining companies, institutions, family maintenance. 100% new and high quality. Adopt of high-quality die head, long life, thread clear. Ease of use, convenient to carry and durable. Lightweight and compact hand design, save labor. Apply to the thread work of galvanized pipe and iron pipe. Powerful motor, increase work efficiency, shorten the construction time.
Includes 6 screw nozzle heads: 1/2 ", 3/4", 1 ", 1-1 / 4", 1-1 / 2 "& 2". Note: Keep adding the lubricating oil as you use it. We promise that every item has been sent. But sometimes there is also 0.3% package lost during transport.
Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, Please tell us the problem in details and Please con-tact us within 14 days after you receive the package.We will provide you the best solution for any problem with the item. Due to time zones, our reply to your questions may not be immediately. But within above working time, we will reply you-= within 24 hours. If it's non-workdays, please kindly be patient and wait till Monday. Please feel free to con-tact us if you have any questions. This item is in the category "Business & Industrial\Light Equipment & Tools\Pipe Tools\Pipe Threaders, Taps & Dies". The seller is "balalastore8" and is located in this country: CH. This item can be shipped to United States, all countries in Europe.